華為模擬器-三次交換機、鏈路捆綁、單臂路由綜合實驗

• 交換機SW1命令
• 交換機SW2命令
• 交換機SW3命令
• 交換機SW4命令
• 路由器R1命令

交換機SW1命令

劃分vlan [Huawei]vlan batch 10 20 interface Ethernet0/0/1 port link-type access port default vlan 10interface Ethernet0/0/2port link-type accessport default vlan 20配置trunkinterface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan allinterface GigabitEthernet0/0/2port link-type trunkport trunk allow-pass vlan 2 to 4094

交換機SW2命令

劃分vlan [Huawei]vlan batch 10 20 interface Ethernet0/0/3port link-type accessport default vlan 10配置trunkinterface Ethernet0/0/4port link-type accessport default vlan 20interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 2 to 4094

交換機SW3命令

劃分vlan [Huawei]vlan batch 10 20 30 interface GigabitEthernet0/0/1port link-type trunkport trunk allow-pass vlan 2 to 4094interface GigabitEthernet0/0/2port link-type accessport default vlan 30在三層交換機的vlanif里配置網關和直連路由的IP地址interface Vlanif10ip address 192.168.10.1 255.255.255.0interface Vlanif20ip address 192.168.20.1 255.255.255.0interface Vlanif30ip address 12.0.0.1 255.255.255.252配置默認路由 ip route-static 0.0.0.0 0.0.0.0 12.0.0.2

交換機SW4命令

劃分vlan interface Ethernet0/0/1 port link-type access port default vlan 30interface Ethernet0/0/2 port link-type access port default vlan 40將g0/0/1到g0/0/2接口進行鏈路捆綁，并且設置為trunk口，允許所有vlan通過。 [Huawei]int Eth-Trunk 1 [Huawei-Eth-Trunk1]trunkport g 0/0/1 to 0/0/2 [Huawei-Eth-Trunk1]port link-type trunk [Huawei-port-group-trunk]port trunk allow-pass vlan all [Huawei-port-group-trunk]un sh

路由器R1命令

[Huawei]int g0/0/0 [Huawei-GigabitEthernet0/0/0]ip add 12.0.0.2 30 [Huawei]int Eth-Trunk 1 [Huawei-Eth-Trunk1]trunkport GigabitEthernet 0/0/1 to 0/0/2將路由器R1設置成單臂路由。 interface Eth-Trunk1.30dot1q termination vid 30ip address 192.168.30.1 255.255.255.0arp broadcast enableinterface Eth-Trunk1.40dot1q termination vid 40ip address 192.168.40.1 255.255.255.0arp broadcast enable

總結

以上是生活随笔為你收集整理的华为模拟器-三次交换机、链路捆绑、单臂路由综合实验的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。