intel SSD Toolbox SMART信息

解釋：
03 – Spin Up Time （磁頭加載時間）
The average time it takes the spindle to spin up. Since an SSD has no moveable
parts, this attribute reports a fixed raw value of zero (0) and a fixed normalized
value of 100. Use the Raw value for this attribute.
（SSD沒這東西，所以這個值 固定為0）

04 – Start/Stop Count （開始/停止計數）
This type of event is not an issue for SSDs. However, hard disk drives can
experience only a finite number of these events and, therefore, must be tracked.
This attribute reports a fixed value of zero (0) and a fixed normalized value of 100.
Use the Raw value for this attribute.
（不知道，反正數值無意義）

05 – Re-Allocated Sector Count （重映射扇區數）
This attribute shows the number of retired blocks since leaving the factory (also
known as a grown defect count).
The lithography (litho) of your drive determines which count you should use. Refer
to the drive name in the Select a Drive section. A ―1‖ in the twelfth position
indicates a 50nm drive, while a ―2‖ indicates a 34nm. For example in Figure 22:
SSDSA2M160G2GN indicates a 34nm drive.
For 50nm drives, the normalized value has an initial value of 100 but counts up from
1 for every 4 grown defects. The normalized value of this attribute becomes 1 when
there are 4 grown defects; the value is 2 when there are 8 grown defects, etc. See
the following table for details.

?

（隨著重映射扇區數的增長而增加【G1，G2不同】）

09 – Power-On Hours Count （通電時間）
This attribute reports the cumulative number of power-on hours over the life of the
device. Use the Raw value for this attribute.
Note: The On/Off status of the device initiated power management (DIPM) feature affects
the number of hours reported.
If DIPM is turned ―On‖, the recorded value for power-on hours does not include
the time that the device is in a ―slumber‖ state.
If DIPM is turned ―Off‖, the recorded value for power-on hours should match the
clock time, as all three device states are counted: active, idle and slumber.
（累積通電時間）

0C – Power Cycle Count （通斷電次數）
This attribute reports the cumulative number of power cycle events (power on/off
cycles) over the life of the device. Use the Raw value for this attribute.
（開關機的次數）

C0 – Unsafe Shutdown Count （異常關機次數）
This attribute reports the cumulative number of unsafe (unclean) shutdown events
over the life of the device. An unsafe shutdown occurs whenever the device is
powered off without STANDBY IMMEDIATE being the last command. Use the Raw
value for this attribute.
（非正常斷電后增長）

E1 – Host Writes （數據寫入量）
This attribute reports the total number of sectors written by the host system. The
raw value is increased by 1 for every 65,536 sectors written by the host. Use the
Raw value for this attribute.
（SSD數據寫入量）

E8 – Available Reserved Space （可用預留空間）
This attribute reports the number of reserve blocks remaining. The attribute value
begins at 100 (64h), which indicates that the reserved space is 100 percent
available. The threshold value for this attribute is 10 percent availability, which
indicates that the drive is close to its end of life. Use the Normalized value for this
attribute.
（這個算是顆粒壽命，等于低于10%SSD就離躺倒不遠了）

E9 – Media Wearout Indicator （閃存磨耗指數）
This attribute reports the number of cycles the NAND media has experienced.
The normalized value declines linearly from 100 to 1 as the average erase cycle
count increases from 0 to the maximum rated cycles.
Once the normalized value reaches 1, the number does not decrease, although it is
likely that significant additional wear can be put on the device. Use the Normalized
value for this attribute.
（如E8上面，等到低于10%，在沒有預留可用空間的情況下，跌的可快了呢- -）

B8 – End to End Error Detection Count （端對端錯誤監測數）
This attribute is only available for 34nm, G2 drives and counts the number of times
errors are encountered during logical block addressing (LBA) tag checks on the data
path within the drive. Use the Normalized value for this attribute.
（LBA映射錯誤增長的數值？）

?

2. SandForce

SandForce 12xx/15xx 主控的SMART定義可以由SFtoolbox查看。點我下載
SandForce的SMART定義在幾次更新固件后做了點小修改，所以固件不同可能有差別。
大致定義的詳細解釋如下：

ID 屬性 解釋

1 Raw Read Error Rate 底層數據讀取出錯率

5 Retired Block Count 不可使用的壞塊計數 （公式比較怪。。這個值不準，新固件都為100）

9 Power On Hours Count 累計加電時間

12 Power Cycle Count 設備通電周期

171 Program Fail Count 編程錯誤計數

172 Erase Fail Count 擦除錯誤計數

174 Unexpected Power Loss Count 不正常掉電次數

177 Wear-Range Data 顯示最大磨損塊和最小磨損塊相差的百分比

181 同171定義相同

182 同172定義相同

187 Reported Uncorrectable Errors 不可修復錯誤計數

194 顯示溫度的，基本可以忽略（假的）

195 On the Fly Reported Uncorrectable Error Count 實時不可修復錯誤計數

196 Reallocated Event Count 重映射壞塊計數

231 SSD Life left SSD剩余壽命
新盤為100，當顯示為10，代表P/E用完了，但是還有備用空間可以替換，顯示0代表盤上數據為只讀。

241 lifetime write froms host 來自主機的寫入數據量總數（64G更新一次）

242 lifetime write froms host 來自主機的讀取數據量總數（64G更新一次）

對于SandForce主控的SMART,我感覺作為用戶只要密切關注241,242兩個值就能知道自己讀寫了多少數據，關注231值的變化大致判斷解剩余壽命。

?

?

3. Micron 鎂光

C300作為首款SATA 6Gbps的SSD主控，主控型號為Marvell 88SS9174-BJP2，固件由鎂光開發。
目前還沒有自家的Toolbox，SMART定義大致如下：（可能會變化）

ID 屬性 解釋

1 Raw Read Error Rate 底層數據讀取出錯率

5 Re-allocated Sectors Count 使用中新增的壞塊數

9 Power On Hours Count 累計加電時間

12 Power Cycle Count 設備通電周期

170 Grown Failing Block Count 替換壞塊計數

171 Program Fail Count 編程錯誤計數

172 Erase Fail Count 擦除錯誤計數

173 Wear Leveling Count 平均擦寫次數

174 Unexpected Power Loss Count 不正常掉電次數

181 Non-4k Aligned Access 非4KB對齊訪問數

183 SATA Interface Downshift 接口降級次數計數

187 Reported Uncorrectable Errors 不可修復錯誤計數

188 Command Timeout 指令超時計數

189 Factory Bad Block Count 出廠壞塊計數

196 Re-allocation Event Count 壞塊重映射事件計數

197 Current Pending Sector Count 值永遠為0

198 Smart Off-line Scan Uncorrectable Error Count 自檢時發現的不可修復錯誤

199 Ultra DMA CRC Error Rate 主機到接口之間傳輸CRC錯誤率

202 Percentage Of The Rated Lifetime Used 剩余壽命（MLC 5000 / SLC 100000計算)
百分比從100開始跌

206 Write Error Rate 底層數據寫入出錯率

我覺得最主要的是那個173/AD的值，那個值是平均塊擦寫次數，用戶可以靠它判斷自己的盤剩余壽命。

?

4. Indilinx

著名的韓國主控廠牌，主控特點為有著優秀的連續讀寫，家族有Barefoot, Barefoot Eco和Amigos.
Smart定義可以用官方工具查看。
大致定義的詳細解釋如下：

ID 屬性 解釋

1 Raw Read Error Rate 底層數據讀取出錯率

9 Power On Hours Count 累計加電時間

12 Power Cycle Count 設備通電周期

184 Init Bad Block Count 壞塊數

195 Program Failure block Count 編程錯誤塊計數

196 Erase Failure block Count 擦除錯誤塊計數

197 Read Failure block Count 讀取錯誤塊計數（不可修復錯誤）

198 Total Count of Read Sectors 總讀取頁數

199 Total Count of Write Sectors 總寫入頁數

200 Total Count of Read Command 總讀取指令數

200 Total Count of Write Command 總寫入指令數

202 Total Count of error bits from flash 總閃存錯誤bit數

203 Total Count of Read Sectors with correct bits error 總修復bit錯誤的讀取頁數字

204 BAD Block Full Flag

205 Max P/E Count 最大可編程/擦除次數 MLC 5000/10000 or SLC 100000

206 Erase Count Min 最小擦寫次數

207 Erase Count Max 最大擦寫次數

208 Erase Count Average 平均擦寫次數

209 Remaining Life % 剩余壽命百分比

210 BBM Error Log 壞塊管理錯誤日志

211 SATA Error Count CRC (Write) SATA 主機 <->接口CRC寫入錯誤計數

212 SATA Error Count HANDSHAKE (Read) SATA 主機 <->接口讀取錯誤計數

?

總結

以上是生活随笔為你收集整理的各种SSD SMART 信息 转的全部內容，希望文章能夠幫你解決所遇到的問題。

如果覺得生活随笔網站內容還不錯，歡迎將生活随笔推薦給好友。